Bookmark and Share
KitchenAid 9758377-002

KitchenAid 9758377-002

From YouserGuide

Jump to: navigation, search
You can edit and write guides yourself, or if you prefer, just send your input to guides@youserguide.com

9758377 (Product)
Pg. 1- 2 -3-4-5-6-7-8-9-10-11-12

Products referring to this guide:-Whirlpool 4RF302BXK-KitchenAid 4RF302BXK-Whirlpool 4RF315PXMQ0-KitchenAid 4RF315PXMQ0-Roper FEP310K:more

Enter your
Part number


background image
2
INSTALLATIONREQUIREMENTS
ToolsandParts
Gather the required tools and parts before starting installation.
Read and follow the safety instructions provided with any tools
listed here.
Tools needed
Parts supplied
Check that all parts are included.
s
Brackets must be securely mounted to subfloor. Thickness of
flooring may require longer screws to anchor bracket to
subfloor. Longer screws are available from your local hardware
store.
Parts needed
Check local codes. Check existing electrical supply. See
“Electrical Requirements” section.
All electrical connections should be made by a licensed, qualified
electrical installer.
LocationRequirements
IMPORTANT: Observe all governing codes and ordinances.
Failure to meet codes and ordinances could lead to fire or
electrical shock.
s
It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the oven frame behind
the storage drawer panel.
s
The range should be located for convenient use in the kitchen.
s
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
s
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
s
The floor anti-tip bracket must be installed. To install the anti-
tip bracket shipped with the range, see “Install Anti-Tip
Bracket” section.
s
Grounded electrical supply is required. See “Electrical
Requirements” section.
IMPORTANT: Some cabinet and building materials are not
designed to withstand the heat produced by the oven for baking
and self-cleaning. Check with your builder or cabinet supplier to
make sure that the materials used will not discolor, delaminate or
sustain other damage.
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or follow local codes.
Mobile home installations require:
s
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing the
range is adequate as long as it conforms to the standards
listed above.
s
Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be
revised. See “Electrical Connection” section.
s
Tape measure
s
Flat-blade screwdriver
s
Level
s
Hammer
s
Hand or electric drill
s
Channel lock pliers
s
Marker or pencil
s
Masking tape
s
³⁄₈" drive rachet
s
¼" nut driver
s
³⁄₈" and ⁵⁄₁₆" nut driver
s
¹⁄₈" (3.2 mm) drill bit (for
wood floors)
s
³⁄₁₆" (4.8 mm) carbide-tipped
masonry drill bit (for
concrete/ceramic floors)
A.Anti-tip bracket
B.Plastic anchors (2)
C.#10 x
¹⁄₂ " screws (2)
A
B
C
Help YG remain FREE
Advertise with YG